HamAntCal vs HamLog Usage & Stats

HamAntCal Version 3.5 (Ham Antenna Calculator) will simply and intuitively calculate for you the starting length needed for constructing your antennas in feet/inches or in metric. It will calculate the starting length for "Dipole's", "Inverted Vee's", "Vertical's" and has a page for calculating 1/8, 1/4, 1/2, 5/8 and "Full Wave" length. In this update: ▪HamAntCal has been updated to 64 bit and iPhone X ▪New updated interface and settings menu ▪New in app purchase to update features ▪This update requires iOS 8.2 and above. --------------------------------------- ▪ HamAntCal works in feet/inches as well as metric. ▪ The easy to use and intuitive interface makes it easy to calculate starting lengths for building your antennas. It will calculate the starting length for "Dipoles", "Verticals" and "Inverted Vee" antennas. There is also a page for calculating 1/8, 1/4, 1/2, 5/8 and "Full Wave" length. ▪ I have come across a lot of different and conflicting information for calculating the length of an "Inverted Vee" antenna. Some say subtract 2 to 5 percent based on the angle of the wires. Others say to add a percentage based on the angle of the wires down from horizontal. I decided to test this before releasing this app. First I calculated for a "Dipole" using the "Dipole" calculator. Then I put together a "Dipole" with a support for the center insulator as well as the ends. I measured the resonant frequency with an antenna analyzer. Then I brought the ends down towards 45 degrees from horizontal. As the ends were lowered the resonant frequency increased. This means that the length of the "Inverted Vee" would need to be increased to stay resonant at the same frequency as the dipole. The "Inverted Vee" calculator has a slider that starts up with an angle of 45 degrees and can be adjusted down to 20 degrees continuously re-calculating as it is moved. This corresponds to about 4.5 to 2 percent added to the length of the "Inverted Vee". ▪ No antenna calculator can give exact results in every case. Much will depend on the wire used, the height above ground, the ground itself, nearby objects, etc…. It's always a good practice to add a little extra wire and then trim up to the desired frequency. ▪ This calculator will calculate from 30 Khz to 500Mhz for the "Dipole", "Vertical" and "Length" calculators. The maximum for the "Inverted Vee" calculator is 60MHz. ▪ This calculator does not give exact measurements and the results will need to be trimmed using an antenna analyzer or SWR meter to the exact frequency after installation. Leave some extra wire on each section for trimming and wrapping around the insulators. ▪ Keep in mind that there are a lot of factors that can affect the resonant frequency of an antenna. At VHF and above even a small change in the length or diameter of an element can make a large change in the resonant frequency of an antenna even more so than at lower frequencies. This calculator just provides the starting length for building an antenna and proper matching methods will need to be used. ▪ Please be safe while building your antennas. Always use the proper safety equipment. Never build your antenna where it can come in contact with power lines, this includes the supports as well as the antenna itself and feed lines. BE SAFE! ▪ Although I have had good results using this calculator the results are not guaranteed. Always add some extra length and trim the antenna to frequency (it's much easier to trim than it is to add wire to the antenna). Please feel free to contact me with suggestions, problems, compliments, ideas for improvements or additions to HamAntCal. Your ratings are appreciated.

Apple App Store
Paid
Utilities

Store Rank

- -

HamLog

Now with rig control! See http://pignology.net/pigtail HamLog is an amateur radio logging and tools application. It is meant for use when operating portable from the field or mobile (drive safe!). It does a lot more than just logging, see the list below. HamLog supports iPhone, iPod Touch and iPad. Features: * Contact Logging and search * Rig control via the Pigtail device from Pignology http://pignology.net/pigtail * Create A Log - Custom Log * QRZ XML Integration for QRZ Subscribers * HamQTH XML Integration * Export via email as ADIF, CSV, or eQSL.cc * Import ADIF * Automatic name/QTH resolution based on callsign (either QRZ XML, HamQTH (free), or Pignology DB (free)) * Independent callsign look up tool * QRZ XML Subscriber Support * CloudSynch: Synch your contacts to the web and other iOS/Mac devices. See http://hamlog.it for more information. * Voice Macros: record yourself and play to VOX * HamStack Control interface: see http://hamstack.com for more information. * QSO Recording * Great Circle Maps * Q signal list * IARU Prefixes List * DXCC Entities List * US Band Plan * International Band Plans * QRZ Look Up via Web * Dupe Finder * Latest DX Spots from DX Summit * ADIF Export, both full and time range * CSV Export * Grid Square tool using GPS * Manual Grid Square Calculator given lat/long * Bearing (and long path) calculation given two grid squares, * WWV Propagation report * Contest Calendar * DXpedition Calendar * Wavelength Calculator * UTC Clock * ITU Phonetic Alphabet * CW Helper: plays single character upon selection * Temperature Converter * Length Converter * RST Explained info * DX Cluster - real time telnet access * Grid to map - enter gridsquare and it will display it on a map * Solar Data from N0NBH (www.hamqsl.com/solar) * DTMF Tone Generator * Net Lists and notifications * Part 97 - Full Text * Field Day Logging * iTunes File Sharing - For data backup and ADIF import - Drop somelogfile.adi into the file sharing pane and press Tools -> Import ADIF. somelogfile.adi should be lowercase until I get an update to recognize uppercase filenames. * Landscape and Portrait on the iPad *** I try to implement just about every request I receive and fix just about every complaint I receive or see in the reviews. If you leave a complaint in a review please leave your callsign so I can get in touch with you to fix your problem, or email me directly. I cannot reply to reviews. Please NOTE: This application is not meant to replace a more formal method of logging such as a computer based logging application or the classic paper method. It is more for quick logging while portable or mobile. Personally, I transfer all contacts to paper after coming back from field QRP fun. Regarding IMPORTING: As of December 8, 2010, HamLog support importing ADIF files. Please visit http://n3wg.com/hamlog for an example of how to import. I will happily respond to feedback, entertain feature requests, and answer questions directly, please contact me at the email address listed on n3wg.com or QRZ. Field Day Logging Info: Sections logged include: Date/time,Mode, Band, Callsign, Class, Section, Operator, Comment Exporting: Exporting logs from the Field Day tool is via e-mail in the form of a CSV file that any spreadsheet program can open. Dup Detection: The app does the standard dup detection you would see in a PC/Mac based app. There is no inter-device dup detection. Dup detection between devices is an exercise left to the exported spreadsheet application of choice. iPad Specifics: Sections worked are shown vs sections not worked for each zone. NOTE: While I try my best to ensure this Field Day logger is fault tolerant, I can make no guarantees or warranties. Please test and become familiar with it before using it live during Field Day. 73, N3WG http://pignology.net